GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 205

Page: 205 / 366

•

The restart of the K2 Media Server after it is configured is complete

This task is required for NAS server functionality.

1. Verify that the K2 Media Server has restarted by opening the MS-DOS command prompt and

use the “ping” command.

2. In the K2Config application tree view, under the K2 Media Server select the File System Server

node.

The File System Server Configuration page appears.

3. Click

Check

and verify that the V: drive is shared.

The K2 Nearline SAN configuration is complete.

Configuring the redundant nearline K2 SAN

Work through the topics in this section sequentially to configure a redundant nearline (Tier 3) K2
SAN.

Prerequisites for initial configuration - Nearline K2 SAN

Before beginning your initial configuration, make sure the devices of the K2 SAN meet the following
prerequisites.

Control point PC

•

Ethernet cable connected

•

Control Point software installed

•

Control network IP address assigned

•

Network communication over the control network with all other K2 devices

•

Power on

Ethernet switch

•

Ethernet cables connected

•

Control network IP address assigned

•

VLANs set up

•

Trunks set up

•

Power on

K2 Media Server

•

Ethernet cables connected

•

Fibre Channel cable connected

•

Redundant servers connected by serial cable

•

Software installed, as from the factory, including QuickTime 7

02 February 2012

K2 SAN Installation and Service Manual

205

Configuring and licensing the K2 SAN

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Search results

Summary of Contents for K2 BASECAMP EXPRESS

Reviews:

Related manuals for K2 BASECAMP EXPRESS

Brands by name

Popular brands

GRASS VALLEY K2 BASECAMP EXPRESS, Installation And Service Manual

Search results

Summary of Contents for K2 BASECAMP EXPRESS

Reviews:

Related manuals for K2 BASECAMP EXPRESS

Brands by name

Popular brands