GRASS VALLEY K2 BASECAMP EXPRESS Installation And Service Manual Download Page 203 | Manualshive

Page: 203 / 366

background image

7. Verify media file system parameters.

Do not edit the configuration file for the media file system.

8. Click

Accept

.

A “…Please wait…” message box displays progress and a “…succeeded…” message confirms
the process is complete.

A message informs you that you must restart the server, however the restart at the end of the
Configure K2 Server wizard suffices, so you do not need to restart now.

9. Close the Storage Utility.

NOTE: Do not attempt to start SAN-attached systems or otherwise bring the SAN online until
instructed to do so by the documented procedure.

Next, continue with configuring the server using the K2Config application.

Configuring NH server - Part 2

Configure File System Server Configuration page - NH server

Prerequisites for connected K2 RAID storage:

•

Network and SNMP settings configured

•

Disks bound

•

New file system made

This page checks on the file system server role. The server also functions as a file system client,
which is also checked from this page.

1. In K2Config open the server's File System Server Configuration page, if the page is not already

open.

02 February 2012

K2 SAN Installation and Service Manual

203

Configuring and licensing the K2 SAN

«
...
201
202
203
204
205
...
»

Summary of Contents for K2 BASECAMP EXPRESS















































































































































































































































































































































































Reviews:

No comments

Related manuals for K2 BASECAMP EXPRESS

Brand: Jensen Pages: 18

GUARDIAN SERIES

Brand: Generac Power Systems Pages: 12

Brand: Mase Pages: 22

Brand: B&B Electronics Pages: 2

Pocketdish AV402E

Brand: Dish Network Pages: 2

Brand: Gbxpoint Pages: 4

Brand: Lampizator Pages: 32

Brand: Wacker Neuson Pages: 36

Brand: Zlpower Pages: 24

Brand: M-system Pages: 5

WinFast Wi2000D

Brand: Leadtek Pages: 2

Proxeo Ultra PB-510

Brand: W&H Pages: 52

Brand: Baumer Pages: 32

Brand: Balluff Pages: 2

Brand: Audio Technica Pages: 11

EASI ATM IND2x2 Series

Brand: Teleste Pages: 28

Brand: Carbest Pages: 22

Brand: Xantrex Pages: 344

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands