GRASS VALLEY IQUCP25 User Manual Download

Page: 93 / 338

UCP

3901

User Manual

Counters

The

Counters

page allows the various counters provided to be cleared down.

Figure 6 - 8:

Counters Page

Parameter

Description

Clear All Sender

Dropped Pkts

Counts the number of data packets an IP sender has had to drop. For

example, if an IP connection were over-subscribed, a sender may drop

data packets to prevent the total IP sending bandwidth being

exceeded.

Clear All CRC

Counts

These count any SDI video CRC errors.

Clear All RTP

Counts

Counts jumps in an Real-time Transport Protocol (RTP) packet ID

sequence in an IP flow. This indicates any lost, dropped or out-of-

sequence RTP packets.
These counters are found on RTP Receiver and Ethernet pages.

Clear All MAC

Error Counts

Counts packets marked as bad, for example, for a data packet CRC

error. Such an error is normally also accompanied by an RTP error

because a packet would be dropped.

Clear All SDI Lost

Lock Counts

Counts the number of times an (internal) SDI signals to the

Multiviewer SDC comes and goes.
These counters are found on the sending spigots pages,

Clear All Global

Counts

Clear all above counts.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands