GRASS VALLEY IQUCP25 User Manual Download

Page: 65 / 338

UCP

3901

User Manual

Fig. 5-2: Connecting to UCP

3901 Card RollCall Templates from RollCall Control Panel

8 To configure the multiviwer, see

Getting Started with the Multiviewer

, on page 249.

Connecting to the Multiviewer SDC with RollCall for IQUCP25 / IQUCP50

Card

The Multiviewer SDC consists of two configuration components to which you have to make

separate connections. By default, you connect with RollCall to the:

• IQUCP25 / IQUCP50 card at the IQ modular chassis IP address, at port 2050 (default).
• Multiviewer SDC at the

SFP1

IP address, at port 2051.

PREREQUISITE: The Multiviewer SDC license must have been installed.

1 Connect to the IQUCP25 / IQUCP50 card through it default port 2050. See

First Time

Connection to the UCP

3901 / IQUCP25 / IQUCP50 Card with RollCall

, on page 60.

2 Navigate to the high-speed Ethernet configuration pages for SFP1 and SFP2. See

Ethernet Pages 1 and 2

, on page 101.

3 Set the IQUCP25 / IQUCP50’s IP address for the

SFP1

and

SFP2

Ethernet port IP

addresses.

4 Click

Connect to RollCall Network

button in the main toolbar.

5 Using RollCall, connect to the UCP

3901’s

SFP1

IP address, at port 2051.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands