GRASS VALLEY IQUCP25 User Manual Download

Page: 307 / 338

307

UCP

3901

Multiviewer SDC

Chapter

User Manual

Timer Request Protocol

The

Timer Request Protocol

template allows you to define the IP address of an ‘eTimer’

server device and the IP port number to use. The protocol used is the Plura

Timer

Request Protocol.

Fig. 9-12: Timer Request Protocol Template

Enter information as required, then click

to save.

Table 9-4: RollCall Timer Request Protocol Settings

Setting

Description

IP Address

Set the IP Address of an ‘eTimer’ server device then press

Port

Set the associated port number to use for Timer Request Protocol

messages.

Enabled

Select to enable use of Timer Request Protocol messages.

Note:

Configuring an ‘eTimer’:
An Orbit Timer widget can be configured on a video wall tile in

GV Orbit to be connected to an ‘eTimer’ service.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands