manualshive.com logo in svg

GRASS VALLEY IQUCP25, User Manual, Page: 288 / 338

Share
Download
GRASS VALLEY IQUCP25 User Manual Download Page 288

288

Multiviewer SDC

FEC

FEC

The FEC page allows Forward Error Correction (FEC) Clause 74 (FC) and Clause 108 (RS) 

functionality of IEEE 802.3

3

 to be enabled. FEC performance logging and statistics are also 

available. The FEC to be used is selected through the Card Firmware/Software Version 

options on the Configuration page; see 

Configuration

, on page 281 for more information.

The configuration of this page is the same as for Essence Processing. See 

FEC

, on page 94.

NMOS

The 

NMOS 

page allows various NMOS parameters to be set, allowing the UCP

-

3901 to inter-

operate with other equipment through an NMOS registry. NMOS must be used with SMPTE 

ST 2110 stream transport only.
The configuration of this page is the same as for Essence Processing. See 

NMOS

, on 

page 96.

Ethernet Pages 1 and 2

Ethernet 1 

and

 Ethernet 2 

are the Multiviewer’s high speed media ports. 

Ethernet 1

 is 

identified as 

SFP1

 and 

Ethernet 2

 is identified as 

SFP2

 on the card’s rear panel. See 

Rear 

Panel and Connectors

, on page 32. 

The 

Ethernet

 pages show details and status for each of the Multiviewer’s high speed media 

network interfaces. The UCP

-

3901 defaults to use DHCP for Ethernet port address 

negotiation, but this can be overridden and a static IP address can be specified if required.
The Ethernet configuration for these ports can also be set through the frame’s control 

panel. This is useful when the card is first installed in the frame, to make it quickly 

operational. See 

Local control using the Densité frame control panel to set the Card’s IP 

Addresses

, on page 38.

See 

Ethernet Gb

, on page 295 for information on the 

MANAGEMENT

 / IQ modular chassis 

Ethernet connector. 
The configuration of this page is the same as for Essence Processing. See 

Ethernet Pages 1 

and 2

, on page 101.

3.Ensure the network switch you plan to use supports CL91-RS-FEC. For example, for Cisco products, see 

https://www.cisco.com/c/en/us/td/docs/switches/datacenter/aci/apic/sw/kb/b_Cisco_ACI_and_Forward_
Error_Correction.html

.

Summary of Contents for IQUCP25



















































































































































































































































































































































Reviews:

No comments