GRASS VALLEY IQUCP25 User Manual Download

Page: 260 / 338

260

Getting Started with the Multiviewer

Quick Edit of Project

Fig. 8-9: Project Open in Orbit

To save the project on the local computer in the previously-specified folder:

11 Click

File > Save Project

in the main menu,

or click the

Save Project

icon in the main tool bar.

Quick Edit of Project

To make a visible change to the project:

1 Click the large

Walls

icon and select a wall item in the list, for example, ‘Output 1’.

The selected wall is opened in a Wall Editor.

Fig. 8-10: Project Open in Orbit

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands