GRASS VALLEY IQUCP25 User Manual Download

Page: 210 / 338

210

MADI Processing SDC

Audio Shuffle

Audio Shuffle

The

Audio Shuffle

page allows for incoming audio channels to be routed to any of the

outgoing audio channels through a 64 × 64 matrix. Also available are:

• Mute.
• Tone sources for spigots 1 to 8. See also

MADI Signal Conversion Direction by Spigot

Number

on page 200.

• Mapping presets.

Figure 7 - 16:

Audio Shuffle Configuration Page showing a

pass-though

setting

Parameter

Description

Spigot Select

Select the spigot on which you want to configure the audio options.

Num Audio Flows Shows the number of audio flows present on the currently-selected

spigot. See the

Num Audio Flows

parameter in

Input Spigots

page 201 and

Output Spigots

on page 206.

Use the Scroll Bars to view all input and output channels: 1 to 64

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands