GRASS VALLEY IQUCP25 User Manual Download

Page: 173 / 338

173

UCP

3901

User Manual

Information Display

The

Information

display pane appears at the top of each page, and shows basic

information on the input and status of the card. The information to be displayed is defined

on the

Video Selection

and

Information Select

panes to the right of the

Information

display.

Figure 7 - 1:

Information and Selection Panes

Selecting the Information to Display

• Select

MADI Status

Network Status

from the

Information Select

pane as required.

The selected information type is displayed on the

Information

display pane. When

MADI

Status

is selected, the

Information

display pane shows the following for each of the card’s

inputs and outputs.

•

MADI signal present.

•

All channels have tone present.

•

Some audio channels have tone present.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands