GRASS VALLEY IQUCP25 User Manual Download

Page: 163 / 338

163

UCP

3901

User Manual

Setup

The

Setup

page displays basic information about the card, such as the serial number and

software version. This information may be required by Grass Valley Support if technical

assistance is needed. Use the functions on the page to restart the card or to return all

settings to their factory or default settings.

Figure 6 - 40:

Setup Page

The

Setup

pane displays technical information on the UCP

3901 / IQUCP25 / IQUCP50. You

may be asked for these details by Grass Valley support if you need technical assistance.

Parameter

Description

Product

Name of the card.

Software Version

Currently installed software version number.

Firmware Version Currently installed firmware version number.
Serial No.

Card serial number.

SW Build

Factory software build number. This number identifies all parameters

of the card.

Operating system version number.

Rear ID

Rear panel type. See:

• For the UCP

3901:

Rear Panel and Connectors

on page 32.

• For the IQUCP25 / IQUCP50:

Images of Rear Panel Connectors

page 46.

Firmware Build

Set

FPGA Firmware build date.

Main PCB

Printed Circuit Board version number.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands