GRASS VALLEY IQUCP25 User Manual Download

Page: 162 / 338

162

Essence Processing SDC

Loopback Router

Loopback Router

The

Loopback Router

page is used to control a basic, internal ‘IP routing’ facility, which will

loop IP flows from source spigots back into destination spigots. This is not used in normal

operation. looped-back flows are not transmitted externally: The loop-back routing is all

local to the UCP

3901 / IQUCP Card.

Figure 6 - 39:

Loopback Router Page

To use the Loopback Router:

1 Use the matrix radio buttons to specify which inputs should be routed to which

outputs.

2 Select the

Video Flow to Use

- SMPTE-2022, 2110-20, or VC2 (VC2 is currently

unsupported).

3 Select the

P Secondary

IP fabric

to use (main/backup).

4 When set as required, set

Enable Router Control

to activate routing.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands