GRASS VALLEY IQUCP25 User Manual Download

Page: 160 / 338

160

Essence Processing SDC

RollTrack

RollTrack

The

RollTrack

page sets up RollTrack setting for the UCP

3901 / IQUCP Card to allow

information to be sent, through the RollCall network, to other compatible units connected

on the same network.
The

Source

window lists the RollTrack sources:

Figure 6 - 38:

Source Pane

Parameter

Description

Disable All

When checked, all RollTrack items are disabled.

Index

This slider allows up to 32 distinct RollTrack outputs to be set up.

Dragging the slider selects the RollTrack Index number, displayed

below the slider. Clicking

selects the default preset value.

Source

The source of information that triggers transmission of data is

selected with this control. Dragging the slider selects the RollTrack

source, displayed below the slider. Clicking

selects the default

preset value. When no source is selected,

Unused

is displayed.

Unused:

No RollTracks sent.

Input N OK:

Input N is good.

Input N LOST:

Input N is bad.

Where N is the input number

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands