GRASS VALLEY IQUCP25 User Manual Download

Page: 120 / 338

120

Essence Processing SDC

Input Loss Control

Input Loss Control

The

Input Loss Control

page allows control of the card’s response to signal loss. Select as

required.

Figure 6 - 22:

Input Loss Control Page

Options upon signal loss are:

Option

Operation

Freeze

Picture will freeze.

Black

Picture will cut to black.

TPG

Picture will be replaced by a test pattern output, as set on the

Sender

TPG

page. See

Sender TPG (Test Pattern Generator)

on page 91 for

more information.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands