GRASS VALLEY IQUCP25 User Manual Download

Page: 114 / 338

114

Essence Processing SDC

HDR Receiver Control

HDR Receiver Control

The

HDR Receiver Control

page allows HDR essences to be configured.

Figure 6 - 18:

HDR Receiver Control Pages

Parameter

Description

Transfer Function

SDR:

the HD input video signal meets the Rec. 709 standard.

HDR-HLG:

the Hybrid Log-Gamma input video signal meets the

BT.2100 standard.

HDR-PQ:

the Perceptual Quantizer input video signal meets the

SMPTE ST 2084 standard.

Other:

Other than an option shown above.

Colorimetry

BT709:

the input video signal’s color gamut meets the Rec. 709

standard.

BT2020:

the input video signal’s color gamut meets the Rec. 2020

standard.

Other:

Other than an option shown above.

Color Space

YCbCr:

the input video signal’s color space uses the YCbCr color

model.

ICtCp:

the input video signal’s color space uses the ICtCp color model.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands