GRASS VALLEY 7500NB Instruction Manual Download Page 75 | Manualshive

Page: 75 / 92

background image

7500 Series Instruction Manual

Glossary-1

Glossary

AES

Audio Engineering Society. AES represents
any of the digital audio standards estab-
lished by the Audio Engineering Society.

AES/EBU

Name for a digital audio standards estab-
lished jointly by the Audio Engineering Soci-
ety and European Broadcasting Union. The
sampling frequencies for this standard vary
depending on the format being used.

Alarm

A signal indicating major or minor alarm
conditions.

Alien Matrices

Any matrix which is not a part of the Series
7000 router product line.

All-level Takes

Switch the same input number on all Levels,
to the controlled Destination.

Amezi

Asynchronous Mezzanine board. An RS-
422/RS-232 communications board which
mounts on the 7000 MCPU or a 7000 Com-
munications Interface (CIF) module and pro-
vides RS-422 and RS-232 ports. The
Asynchronous Mezzanine board is one of
several mezzanine boards of differing func-
tionality.

ANC

Active Node Controller. An ANC is commu-
nicating with the MCPU and will appear in a
list of Active Node Controllers when polled
by the GUI. The Enhanced Node Controller
and the Matrix Controller modules also ap-
pear in the list. ANCs include both the pri-
mary and backup Controller modules.

ANSI

American National Standards Institute.

Assignment

Assignment is an action that grants permis-
sion for exclusive control of a resource. Mul-
tiple devices may be assigned permission for
exclusive control of a single device, however
only one may exercise control at a specific
point in time.

Control of particular sources and TieLines
can be Assigned to destinations on a case-by-
case basis. The Assignment system is en-
abled (Machine and TieLine Assignment)
through the GUI Enables menu. Active As-
signments are controlled through the GUI
(on-line, OnLine menu, Assignments sub-
menu) or may be handled by an external au-
tomation or scheduling system.

Backplane (Rear connector channel, Mother-
board)

The circuit board at the back of an electronics
frame where modules (from the front) and
cables (from the rear) are plugged-in.

BNC

Bayonet Neill-Concelman (BNC) connector.
(Named for its inventors). A type of coaxial
cable connector.

BPI

Backplane Interface. This is required for a
Communications Interface module to com-
municate with a MCPU module.

BPS

Button Per Source. Name given to a panel
feature that performs a source take with the
single push of a button.

«
...
73
74
75
76
77
...
»

Summary of Contents for 7500NB





























































































Reviews:

No comments

Related manuals for 7500NB

Brand: YASKAWA Pages: 34

Brand: Vanguard Pages: 4

Brand: ebm-papst Pages: 16

Brand: Draytek Pages: 8

Brand: SUNRICH TECHNOLOGY Pages: 5

OMB-DAQBOARD-3000 Series

Brand: Omega Pages: 108

Brand: Altera Pages: 93

NetVanta 6355 PoE

Brand: ADTRAN Pages: 46

AirStation WHR-G300N

Brand: Hornington Pages: 6

Brand: Cypress Semiconductor Pages: 16

OMB-DAQBOARD-500 Series

Brand: Omega Pages: 48

Brand: MiWire Pages: 24

Brand: PRIZM Pages: 8

LatticeMico GPIO

Brand: Lattice Semiconductor Pages: 28

Brand: Goobay Pages: 20

ARC-12x4 Series

Brand: Areca Pages: 2

Brand: Alcatel Pages: 4

Brand: Matrix Switch Corporation Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands