manualshive.com logo in svg

GRAPHTEC OPS676, User Manual, Page: 6 / 35

Share
Download
GRAPHTEC OPS676 User Manual Download Page 6

6

1. Introduction to the Controller

Features

• Easy Setting from Your Computer

The controller enables you to set up and operate the plotter from your computer. Relevant 

settings are displayed on a single screen and you can easily find the setting that you want 

to see. You can use the driver to start the controller from the print menu in the application 

software and efficiently proceed a series of works ranging from image design to cutting.

* The controller can be started up from PRINTER MENU of the application software with the driver only 

when USB connection is used.

• Saving Tool Conditions

Up to 100 tool conditions that are set in the controller can be saved to the media list. 

Contents in the media list can be saved as a file and loaded to your computer.

• Loading Plotter Setting/Uploading Settings to the Plotter

Tool conditions that are set in the operation panel of the plotter (Condition No. 1 through 8) 

can be loaded to the controller. You can edit the loaded settings in the controller and upload 

them to the plotter.

• Retrieving Information from the Plotter

You can retrieve error and condition information from the plotter and save it as a file.

• Importing/Exporting Advanced Settings

You can save advanced settings to any location on your computer as well as load setting 

files that have been saved.

   

CAUTION

 

• Do not control more than one plotters by the controller. Depending on the operations, the settings 

in the plotters may not be properly controlled.

• When using the Cutting Master 3 / Graphtec Studio, do not use the controller. You will not be 

able to properly control the plotter settings.

Operation Environment

The following system environment (higher environment than one your OS recommends) is 

required to use the controller.

OS

Windows Vista / 7 / 8 / 8.1 / 10 (32 bit/64 bit)

CPU

Intel Pentium 4 / AMD Athlon 64 or greater

Memory

1GB or greater

Monitor

1024 × 768 True Color is supported

USB Interface

USB 2.0 (Full Speed)

Serial Interface

RS-232C compliant

Device

Mouse 

DVD-ROM drive

   

CAUTION

 

• To use the controller, the plotter must be connected to the computer using a USB or RS-232C 

interface. In Simple mode, RS-232C interface is not available.

• If the 7-bit data length of the transfer conditions for RS-232C is set, the half-width Kana characters 

are not properly sent and received. To send and receive them, set the data length to 8-bit. 

When the 7-bit data length of the transfer conditions for RS-232C is set, use the alphanumeric 

characters only. 

For more information about the settings, see "Chapter 9: Setting the Interfaces" in the CE6000 

User's Manual.

Installing the Controller

The controller is installed with the driver when you set up the plotter in Windows Vista / 7 / 8 

/ 8.1 / 10.  

For more information on how to install the controller, see "Setup Manual". 

For information on how to uninstall the controller, see "Uninstalling the Controller" (  page 

33).

Summary of Contents for OPS676




































Reviews:

No comments