GRAPHTEC OPS676 User Manual Download Page 11 | Manualshive

Page: 11 / 35

GRAPHTEC OPS676 User Manual Download Page 11

11

2. Setting Tool Conditions [CONDITION]

Performing one of the following tasks opens the corresponding screen for setting tool

conditions, Setting method is the same for all of the screens. In this section, the [Edit

Conditions] screen is used for explanation.

• In the main screen (  page 9), click [Edit Conditions] to open the [Edit Conditions] screen
• In the [Edit Media List] screen (  page 16), click [Edit] to open the [Edit] screen
• In the [Edit Media List] screen (  page 16), click [New] to open the [New] screen
• In the [Edit Media List] screen (  page 16), click [Copy] to open the [Copy] screen
• In the [Edit Media List] screen (  page 16), click [Load] to open the [Load] screen

In the tool condition setting screens, you can edit a tool condition or create a new one. You

can also run a cutting test under the condition that you set.

Basic Settings

Make the basic tool condition settings.

Media name, Tool type, Force, Speed, Accel, Offset can be set.

CAUTION

• Although installing the controller also installs a standard condition setting file, optimal settings

may differ depending on the use environment, the types of media, applications, and other

factors. To set values, see "Guideline for Settings (for Each Media)" ( page 12), "Guideline for

Settings (When Plotter Pen is Selected)" ( page 12), and "Guideline of Offset Setting (for Each

Cutter Blade)" ( page 12). Be sure to run a cutting test to determine the optimal tool condition

before performing actual cutting.

"Cut Test" on page 14

• Clicking [OK] directly after editing the settings overwrites the tool condition under the current

media name. To create a new tool condition with the settings that you have edited, enter a new

name in [Media Name] and then click [OK].

Reference

• Smaller values for the speed and the acceleration require longer cut time, but the quality is

stable. Set small values for the speed and the acceleration when you cut wide media because

such media may move during a cutting process and good cut quality may not be obtained.

• When you use a plotter pen, set the FORCE to the lowest setting to prolong the pen life. Adjust

the speed so there will be no faint lines.

2

1

7

8

9

10

3

4
5

6

«
...
9
10
11
12
13
...
»

Summary of Contents for OPS676




































Reviews:

No comments