Das empfohlene Schrauben-
Anzugsdrehmoment beträgt:
0,39 Nm.
During installation, a
4kgf.cm screw
tightening torque is
recommended.
During installation, a
4kgf.cm screw
tightening torque is
recommended.
Bind so that the there is
approx. 25 cm between
the monitor connection
cable and the connector.
1, Monitor
3, Threaded hole for mounting
2, Operation key
4, Connector for connecting to module
5, Threaded hole for mounting
6, Nail
7, Monitor In connector
11, Mounting hole
9, Tilting table
10, Clamp
8, Nail
8, Nail
Face cover nails
1
2
1
2
1
2
1
2
1
2
1
2
Monitor connection cable
(40 cm)
Ground cable
Tilting table
Monitor Out connector
During installation, a
4kgf.cm screw
tightening torque is
recommended.
Please note the specifications of the LAN cable you use.
[LAN Cable specifications]
Type: Straight cable
Category: CAT5 or above
Cable length: 10 m or less
1
2
1
2
GND terminal
Tilting table
Please use the display
module fixed to a board, etc.
Please do not connect a LAN cable
with the monitor in connector of
the display module and the LAN connector of the GL7000 main module.
GL7-DISP-UM-151
Thank you very much for buying this GRAPHTEC product.
This product is a display module for recording.
Please use it by installing it on the main module.
These directions describe preparations and cautions before
measurement.
For the details concerning operation procedures etc., read
the User
’
s manual recorded on the CD-ROM (included with
the main module)
Confirmation of the exterior
After opening the package, please confirm that there are no
problems (scratches and dirt) on the exterior before use.
Confirmation of the attached items.
Instruction manual (this book): 1
Tilting table: 1 module
Monitor connection cable (40 cm): 1 pc.
Screws (M4x6): 3 pcs.
Ground cable: 1 pc.
Flat Head Screws (M4
ｘ
10) 2 pcs. (Spare)
If by any chance faults are found, please contact the store where you
bought the item.
* Please note that items mentioned in this book may change without prior notice.
Threaded hole for fixing to the main module
Connector for connecting to the main module
Threaded hole for fixing to the tilting table
(M4 Approx depth 5 mm)
Threaded hole for fixing to the tilting table
(2 places)
Connector for use when extending
cables, and when using the tilting table
1, Monitor
2, Operation key
3, Threaded hole for mounting...
4, Connector for connecting to module..
5, Threaded hole for mounting..
6, Nail......................................
7, Monitor In connector.........
1 Part Names
2 How to Install Module
Explanation of the module's part names and functions.
This explains how to attach the module to the main module.
The display module has 3 basic positions.
A. When the main module is attached...
fitting to the main module.
B. When using the tilting table...
Use the tilting table (at a 15° tilt
angle) to fit to the main module.
C. When extending cables...
Use a commercially available LAN cable,
and attach to a place separated from the display module on the main module.
(After the main module 's face cover is removed)
(After the main module
’
s face cover is mounted)
1, Connect the monitor out contact on the main module and the
monitor in contact on the display module with a commercially
available LAN cable.
2, Pull the nail on the upper-right side of the face cover, and remove
the face cover.
4, Join the display module with the module connector, and insert
into the main module.
5, Attach the fixation screws on the main module (2 places on the
side).
* If the ground cable is not connected,
sufficient performance may not be obtained.
5, Attach the fixation screws of the main module (2 places on the
side).
3, Join the nails on the back of the display module with the inset
part of the main module, and push it in.
1, Install by binding the monitor connection cable with the clamp
on the tilting table.
2, Attach the display module to the tilting table with the attached
fixation screws (2 places).
3, Connect the connector of the monitor connection cable to the
monitor in connector of the display module.
4, Connect the monitor connection cable to the monitor out
connector of the main module and attach the 4 point nails on
the tilting table by fixing them to inset part of the main module
(4 places).
3 Specifications
GL7-DISP (Display Module) Specifications
Item
Display device
Operating portion
touch-panel
Display characters
Backlight
Backlight life
Display screen
Connection cable
(For cable extension)
Accessories
External dimensions
[W
×
D
×
H] (approximate)
Weight
Contents
5.7” TFT color liquid crystal display
(VGA: 640 x 480)
Capacitive touch-panel and key shared use
* Almost all operations can be performed by either the touch-panel or the keys.
Input method: Finger
Operating life: Approx. 50,000,000 times
* It depends on the status of use, etc.
Japanese, English, French, German, Chinese, and Korean
Screen saver function (10, 30 sec.; 1, 2, 5, 10, 30, 60 min.)
50.000 hours (when brightness has decreased to 40%),
changes according to use environment
Wa digital screen, full waveform screen, d
operation screen, X-Y display
* CH number and display CH are designated for when the display of the
d operation screen is digitally enlarged
LAN cable (straight, CAT5 and above, cable length 10 m or less)
* Please purchase a commercially available product
Tilting table 1 module Monitor connection cable (40 cm) 1 pc. Screws (M4
ｘ
6) 3 pcs.
Flat Head Screws (M4
ｘ
10) 2 pcs. (Spare) Groound cable 1 pc.
187
×
34.5
×
119 mm (Not including protruding parts)
530g (Not including the tilting table)
Since the touch-panel in this module is a capacitive touch-panel, it does not
respond by touching it with a pen.
* Please note that if the touch-panel is operated with an object with a sharp edge, it
may scratch and damage the touch-panel.
* Do not touch when your hands are wet.
Nails for fixing to the main module
(4 places)
Clamp for binding the monitor connection cable
Threaded hole for fixing to the display module
8, Nail....................................
9, Tilting table
10, Clamp................................
11, Mounting hole..................
6, Attach the ground cable to the main module (GND terminal)
with the fixation screws attached to the tilting table.
A. This explains how to install when attaching the main module.
B. This explains how to attach the tilting table for use.
C. This explains installation when extending cables.
GL7000
Display Module
USER’S MANUAL
GL7-DISP
When installing or removing the module, please
make sure that the power is off.
1, Remove fixation screws from the main module (2 places on
the side)
GRAPHTEC Corporation
July 1, 2012
