manualshive.com logo in svg

Graphcore IPU-POD128, Build And Test Manual, Page: 104 / 113

Share
Download
Graphcore IPU-POD128 Build And Test Manual Download Page 104

IPU-POD128 build and test guide

(continued from previous page)

host lr7-ipum8bmc { hardware ethernet 70:69:79:20:14:BC; fixed-address 10.1.7.8; }

host lr7-ipum9bmc { hardware ethernet 70:69:79:20:14:38; fixed-address 10.1.7.9; }

host lr7-ipum10bmc { hardware ethernet 70:69:79:20:14:94; fixed-address 10.1.7.10; }

host lr7-ipum11bmc { hardware ethernet 70:69:79:20:13:F4; fixed-address 10.1.7.11; }

host lr7-ipum12bmc { hardware ethernet 70:69:79:20:12:74; fixed-address 10.1.7.12; }

host lr7-ipum13bmc { hardware ethernet 70:69:79:20:12:6C; fixed-address 10.1.7.13; }

host lr7-ipum14bmc { hardware ethernet 70:69:79:20:14:84; fixed-address 10.1.7.14; }

host lr7-ipum15bmc { hardware ethernet 70:69:79:20:16:BC; fixed-address 10.1.7.15; }

host lr7-ipum16bmc { hardware ethernet 70:69:79:20:17:A4; fixed-address 10.1.7.16; }

ipum-gw.conf

root@gbnwp-pod7-1:/etc/dhcp/dhcpd.d/lrack1#

cat ipum-gw.conf

host lr7-ipum1gw {

hardware ethernet 70:69:79:20:24:D1; fixed-address 10.2.7.1; }

host lr7-ipum2gw {

hardware ethernet 70:69:79:20:14:49; fixed-address 10.2.7.2; }

host lr7-ipum3gw {

hardware ethernet 70:69:79:20:12:BD; fixed-address 10.2.7.3; }

host lr7-ipum4gw {

hardware ethernet 70:69:79:20:13:2D; fixed-address 10.2.7.4; }

host lr7-ipum5gw {

hardware ethernet 70:69:79:20:13:05; fixed-address 10.2.7.5; }

host lr7-ipum6gw {

hardware ethernet 70:69:79:20:14:69; fixed-address 10.2.7.6; }

host lr7-ipum7gw {

hardware ethernet 70:69:79:20:14:D5; fixed-address 10.2.7.7; }

host lr7-ipum8gw {

hardware ethernet 70:69:79:20:14:BD; fixed-address 10.2.7.8; }

host lr7-ipum9gw {

hardware ethernet 70:69:79:20:14:39; fixed-address 10.2.7.9; }

host lr7-ipum10gw { hardware ethernet 70:69:79:20:14:95; fixed-address 10.2.7.10; }

host lr7-ipum11gw { hardware ethernet 70:69:79:20:13:F5; fixed-address 10.2.7.11; }

host lr7-ipum12gw { hardware ethernet 70:69:79:20:12:75; fixed-address 10.2.7.12; }

host lr7-ipum13gw { hardware ethernet 70:69:79:20:12:6D; fixed-address 10.2.7.13; }

host lr7-ipum14gw { hardware ethernet 70:69:79:20:14:85; fixed-address 10.2.7.14; }

host lr7-ipum15gw { hardware ethernet 70:69:79:20:16:BD; fixed-address 10.2.7.15; }

host lr7-ipum16gw { hardware ethernet 70:69:79:20:17:A5; fixed-address 10.2.7.16; }

ipum-rnic.conf

root@gbnwp-pod7-1:/etc/dhcp/dhcpd.d/lrack1#

cat ipum-rnic.conf

host lr7-ipum1mx { hardware ethernet 0c:42:a1:78:90:35; fixed-address 10.5.7.1; }

host lr7-ipum2mx { hardware ethernet 0c:42:a1:78:90:d5; fixed-address 10.5.7.2; }

host lr7-ipum3mx { hardware ethernet 0c:42:a1:78:7e:55; fixed-address 10.5.7.3; }

host lr7-ipum4mx { hardware ethernet 0c:42:a1:78:82:65; fixed-address 10.5.7.4; }

host lr7-ipum5mx { hardware ethernet 0c:42:a1:84:ec:3d; fixed-address 10.5.7.5; }

host lr7-ipum6mx { hardware ethernet 0c:42:a1:78:95:65; fixed-address 10.5.7.6; }

host lr7-ipum7mx { hardware ethernet 0c:42:a1:78:96:c5; fixed-address 10.5.7.7; }

host lr7-ipum8mx { hardware ethernet 0c:42:a1:84:f5:85; fixed-address 10.5.7.8; }

host lr7-ipum9mx { hardware ethernet 0c:42:a1:84:ea:85; fixed-address 10.5.7.9; }

host lr7-ipum10mx { hardware ethernet 0c:42:a1:78:7e:65; fixed-address 10.5.7.10; }

host lr7-ipum11mx { hardware ethernet 0c:42:a1:78:8a:0d; fixed-address 10.5.7.11; }

host lr7-ipum12mx { hardware ethernet 0c:42:a1:78:85:55; fixed-address 10.5.7.12; }

host lr7-ipum13mx { hardware ethernet 0c:42:a1:78:89:f5; fixed-address 10.5.7.13; }

host lr7-ipum14mx { hardware ethernet 0c:42:a1:78:8a:4d; fixed-address 10.5.7.14; }

host lr7-ipum15mx { hardware ethernet 0c:42:a1:84:e7:bd; fixed-address 10.5.7.15; }

host lr7-ipum16mx { hardware ethernet 0c:42:a1:78:87:25; fixed-address 10.5.7.16; }

8.6.6 Lrack1: /etc/dhcp/dhcpd.d/lrack2 files

ipum-bmc.conf

root@gbnwp-pod7-1:/etc/dhcp/dhcpd.d/lrack2#

cat ipum-bmc.conf

host lr8-ipum1bmc { hardware ethernet 70:69:79:20:24:D0; fixed-address 10.1.8.1; }

host lr8-ipum2bmc { hardware ethernet 70:69:79:20:14:48; fixed-address 10.1.8.2; }

host lr8-ipum3bmc { hardware ethernet 70:69:79:20:12:BC; fixed-address 10.1.8.3; }

host lr8-ipum4bmc { hardware ethernet 70:69:79:20:13:2C; fixed-address 10.1.8.4; }

host lr8-ipum5bmc { hardware ethernet 70:69:79:20:13:04; fixed-address 10.1.8.5; }

host lr8-ipum6bmc { hardware ethernet 70:69:79:20:14:68; fixed-address 10.1.8.6; }

(continues on next page)

Version: latest (2021-11-25)

100

Summary of Contents for IPU-POD128


















































































































Reviews:

No comments