REGIS
GAZEBO
ASSEMBLY INSTRUCTIONS
GRANGE FENCING LIMITED
Halesfield 21, Telford TF7 4PA
Tel
: 01952 588088
Fax
: 01952 581522
Web
: www.grangefen.co.uk
PLAN
3.2m
3.41m
1.415m
3.71m
4.023m
SIDE ELEVATION
TOP ELEVATION
STEP 14
Attach a third Rafter to
the Roof Centre Support
at right angles to the two
already fitted.
STEP 15
Secure the Rafter to the
Roof Centre Support as
step 12.
STEP 16
Carefully lift the roof
assembly into place on
top of the Posts.
STEP 17
Using screws (
E
) fix each
of the Rafters centrally to
the top of the Posts.
STEP 18
Fix the remaining Rafters
to the Roof Support Centre
and Posts to complete the
roof structure.
STEP 19
Fit the remaining Rafter
Support Strut (
14
) opposing
the one fitted in step 14.
STEP 20
Next, lift one Roof Section
(
15
) into place. Secure in
place using four screws (
B
)
in each side to the Rafters.
STEP 21
Repeat for the remaining
Roof Sections.
STEP 22
Attach a Roof Section Soffit
(
16
) to one of the Roof
Sections using three screws
(
D
).
STEP 23
Repeat for the remaining
Roof Sections.
STEP 24
Insert an Outer Floor Infill
Section (
9
).
STEP 25
Insert Floor Spacer Fillet (
7
)
STEP 26
Fit the Floor Skirting Board
(
17
) to the edge of the floor
using screws (
B
). Two
screws at each end and one
screw in the centre top.
All Grange Gazebos are made of planed, pressure treated and FSC certified timber and as such are guaranteed against rot for a minimum of 15
years. However, it must be remembered that as a natural product, timber is subject to movement and weathering as it seasons. It is not
uncommon for small splits to occur when drying and warping when timber is allowed to dry too rapidly. These will normally go back when
humidity rises. It is nature at work and not considered a fault.
Its colour will also change with time. A retreatment, as required with a proprietary wood treatment is recommended.
CARE OF YOUR GAZEBO
FITTING PANELS TO YOUR GAZEBO
Choose the preferred Panels from the list provided.
Two options are available for fitting them into your Gazebo.
OPTION 1
Fit the right angle brackets to the posts approx. 150mm from
the top and bottom of where the panel will be fixed using M3.5
x 35mm screws. Ensure the bracket will fit on the inside of the
panels. Fix the panels in place using M3.5 x 35mm screws.
OPTION 2
The panels may be fixed in place by screwing at an angle
through the panel into the post. It is advisable to use
M4 x 70mm screws for this purpose.
Note:
Brackets and screws will be provided with the chosen panel.
17
8
11
13
9
15
12
16
12
10
6
1
3
4
5
7
13
16
E
D
D
13
10
STEP 14 - 16
STEP 18 - 22
D
B
B
B
B
B
INITIAL ROOF
FIXING WITH
3 RAFTERS
STEP 17
FIXING
RAFTERS
TO POSTS
STEP 20
SCREW
ROOF
SECTIONS
THROUGH
FRAME
ON THE
UNDERSIDE
STEP 24 - 26
FIXING
OUTER FLOOR
AND SKIRTING
SECTIONS
EACH FLOOR
SKIRTING
BOARD FIXED
WITH 5 SCREWS
2 SCREWS AT
ENDS ANGLED
INTO JOIST
AND FLOOR
FILLET
6
8
9
6
8
3
7
17
B
B
B
7
9
17
13
15
Mixed Sources
Product group from well-managed
forests and other controlled sources.
Cert No. SGS-COC-0100
www.fsc.org
© 1996 Forest Stewardship Council
MAR 07 - ISSUE 1