background image

Instruction Manual

GRANDVIEW  REPRODUCING  GENUINE  COLORS

Recessed-Ceiling 

Motorized Projector Lift

Applicable Model
GPCK-ME500
GPCK-ME1000
GPCK-ME2000
GPCK-ME3000
GPCK-ME4000

Cautious

Warnings

Caution

Please do not take apart the 
accessories of mounting bracket

Do not 
take apart 

Grandview Crystal Screen Canada Ltd.

#11- 3751 North Fraser Way,
Marine Way Business Centre,
Burnaby, BC, Canada  V5J 5G4
Tel: 1-604-412-9777    Fax: 1-604-412-9796
Website: www.grandviewscreen.ca

Guangzhou Grandview Crystal Screen Co., Ltd.

P.O. 511400 Federal Ind. Zone No. 363, Yushan West Road,
Shiqiao, Panyu District, Guangzhou, Guangdong, China
Tel: +8620-8489-9499   Fax: +8620-8480-3343
Website: www.grandviewscreen.com
                

Please read being installation:

Thank you for purchasing this product. 
Please read the instruction manual 
carefully to ensure this projector lift is 
suitable for your installation environment. 

This product should only be installed by a qualified technician. 

Please review the manual carefully to ensure it is properly installation and to avoid injury.

The ceiling used must have a minimum load bearing of 15KG.

For projector lift assembly only

Maximum weight:

25KG
25KG
20KG
15KG
15KG

Summary of Contents for GPCK-ME500









Reviews: