manualshive.com logo in svg

Grandstream Networks UCM6510, User Manual, Page: 378 / 483

Share
Download
Grandstream Networks UCM6510 User Manual Download Page 378

 

P a g e

 | 

377 

 

UCM6510 IP PBX User Manual 

Version 1.0.20.31 

IAX SETTINGS 

 

The UCM6510 IAX global settings can be accessed via Web GUI

PBX

IAX Settings

. 

IAX Settings/General 

Table 114: IAX Settings/General 

Bind Port 

Configure  the  port  number  that the  IAX2  will  be  allowed  to  listen  to.  The 

default setting is 4569. 

Bind Address 

Configure the address that the IAX2 will be forced to bind to. The default 

setting is 0.0.0.0, which means all addresses. 

IAX1 Compatibility 

Select to configure IAX1 compatibility. The default setting is "No". 

No Checksums 

If  selected,  UDP  checksums  will  be  disabled  and  no  checksums  will  be 

calculated/checked on systems supporting this feature. The default setting 

is "No". 

Delay Reject 

If  enabled,  the  IAX2  will  delay  the  rejection  of  calls  to  avoid  DOS.  The 

default setting is "No". 

ADSI 

Select to enable ADSI phone compatibility. The default setting is "No". 

Music On Hold Interpret 

Specify  which  Music  On  Hold  playlist  this  channel  would  like  to  listen  to 

when being put on hold. This music playlist is only effective if this channel 

has no music playlist configured and the bridged channel putting the call on 

hold has no "Music On Hold Suggest" setting. 

Music On Hold Suggest 

Specify  which  Music  On  Hold  playlist  to  suggest  to  the  bridged  channel 

when putting the call on hold. 

Bandwidth 

Configure the bandwidth for IAX settings. The default setting is "Low". 

 

IAX Settings/Registration 

Table 115: IAX Settings/Registration

 

IAX Registration Options

 

Min Reg Expire 

Configure  the  minimum  period  (in  seconds)  of  registration.  The  default 

setting is 60. 

Max Reg Expire 

Configure  the  maximum  period  (in  seconds)  of  registration.  The  default 

setting is 3600. 

IAX Thread Count 

Configure the number of IAX helper threads. The default setting is 10. 

IAX Max Thread Count 

Configure the maximum number of IAX threads allowed. The default setting 

is 100. 

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Reviews:

No comments