Grandstream Networks UCM6510 User Manual Download Page 260

Page: 260 / 483

P a g e

259

UCM6510 IP PBX User Manual

Version 1.0.20.31

Conference Settings

Figure 151 : Video Conference Basic settings

Table 77: Video Conference Basic Settings

Basic Settings

Video Conferencing

This option should be enabled in order to activate the Video Conference

feature.

Bind UDP Port

Configure the UDP port number for MCM. The standard UDP port for MCM

is 5062.

Packet Loss Retransmission

Configure to enable Packet Loss Retransmission.

FEC

If enabled, the Forward Error Correction (FEC) will be activated. The

default setting is "No".

Enable Talk Detection

If enabled, the AMI will send the corresponding event when a user starts

or stops talking.

DSP Talking Threshold

The amount of time (ms) that sound exceeds what the DSP has

established as the baseline for silence before a user is considered to be

talking. This value affects several operations and should not be changed

unless the impact on call quality is fully understood.

DSP Silence Threshold

The amount of time(ms) that sound falls within what the DSP has

established as the baseline for silence before a user is considered be

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands