Grandstream Networks UCM6510 User Manual Download Page 203

Page: 203 / 483

P a g e

202

UCM6510 IP PBX User Manual

Version 1.0.20.31

DATA TRUNK

The UCM6510 E1/T1/J1 interface also supports data trunk function that allows users to access Internet.

Users can select HDLC, HDLC-ETH, Cisco and PPP protocol for the data trunk.

To use data trunk,

1. Go to Web GUI



PBX Settings



Interface Settings



Digital Hardware

page and click

to create

a new group. Designate a channel for data trunk usage in the group setting.

2. Go to Web GUI



Extension/Trunk



Data Trunks

page, click on

to edit the data trunk.

Save the configuration and click on “Apply Changes” for the change to take effect.

4. Once connected, the data trunk will periodically ping and check the status, with status indicator shown

for the data trunk on the web page. The status indicator shows

if connected successfully.

5. If the user happens to lose connection or experience unstable connection, click on

to reconnect to

help resolve the problem.

Figure 107: Data Trunk Web Page

Figure 108: Data Trunk Configuration

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands

Grandstream Networks UCM6510, User Manual

Search results

Summary of Contents for UCM6510

Reviews:

Related manuals for UCM6510

Brands by name

Popular brands