manualshive.com logo in svg

Grandstream Networks UCM6510, User Manual

Share
Download
Grandstream Networks UCM6510 User Manual Download Page 156

 

P a g e

 | 

155 

 

UCM6510 IP PBX User Manual 

Version 1.0.20.31 

must remain unpressed for the PBX to consider the event as a valid flash 

event. The valid range is 30ms to 1000ms. The default setting is 200ms. 

MAX RX Flash 

Configure the maximum period of time (in milliseconds) that the hook-flash 

must remain unpressed for the PBX to consider the event as a valid flash 

event. The minimum  period  of  time is  256ms  and it  cannot  be modified. 

The default setting is 1250ms. 

Enable Polarity Reversal 

If enabled, a polarity reversal will be marked as received when an outgoing 

call  is  answered  by  the  remote  party.  For  some  countries,  a  polarity 

reversal is used for signaling the disconnection of a phone line and the call 

will be considered as hang up on a polarity reversal. The default setting is 

“Yes”. 

Echo Cancellation 

Specify 

“ON”, “OFF” or a value (the power of 2) from 32 to 1024 as the 

number of taps of cancellation. 

Note: 

When  configuring  the  number  of  taps,  the  number  256  is  not 

translated into 256ms of echo cancellation. Instead, 256 taps mean 256/8 

= 32 ms. The default setting is 

“ON”, which is 128 taps.

 

3-Way Calling 

Configure to enable/disable 3-way calling feature on the user. The default 

setting is enabled. 

Send CallerID After 

Configure the number of rings before sending CID. Default setting is 1. 

Fax Mode 

For  FXS  extension,  there  are  three  options  available  in  Fax  Mode.  The 

default setting is “None”. 

 

None:

 Disable Fax. 

 

Fax  Detect:

  Fax  signal  from  the  user/trunk  during  the  call  can  be 

detected  and  the  received  Fax  will  be  sent  to  the  Email  address 

configured for this extension.   

 

If no Email address can be found for the user, the Fax will be sent to 

the default Email address configured in Fax setting page under Web 

GUI

Call Features

Fax/T.38. 

 

Fax  Gateway

:  If  selected,  the  UCM6510  can  support  conversation 

and  processing  of  Fax  data  from  T.30  to  T.38  or  T.38  to  T.30.  This 

feature is only available for FXS or FXO port. 

Table 41: FXS Extension Configuration Parameters 

– Features 

Call Transfer 

Call Forward Unconditional 

Configure the Call Forward Unconditional target number. If not configured, 

the Call Forward Unconditional feature is deactivated. The default setting 

Summary of Contents for UCM6510




































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands