Grandstream Networks UCM6200 Series Page 280 User Manual Download

Page: 280 / 469

P a g e

279

UCM6200 Series User Manual

Version 1.0.20.38

Figure 179: Private Intercom

Table 79: Private Intercom Configuration Parameters

Name

Configure paging/intercom group name.

Type

Select "Private Intercom".

Extension

Configure the paging/intercom group extension.

Replace Display Name

If enabled, the UCM will replace the caller display name with Paging/Intercom

name.

Maximum Call Duration

Specify the maximum call duration in seconds. The default value 0 means no

limit.

Custom Prompt

This option is to set a custom prompt for a paging/intercom group to announce

to caller. Click on ‘Prompt’, it will direct the users to upload the customized voice

prompts.

Note

: Users can also refer to the page

PBX Settings

→

Voice Prompt

→

Custom

Prompt

, where they could record new prompt or upload prompt files.

Members

Select available users from the left side to the paging/intercom group member

list on the right.

Paging/Intercom

Whitelist

Select which extensions are allowed to use the paging/intercom feature for this

paging group.

Summary of Contents for UCM6200 Series






















































































































































































































































































































































































































































































Search results

Summary of Contents for UCM6200 Series

Reviews:

Related manuals for UCM6200 Series

Brands by name

Popular brands

Grandstream Networks UCM6200 Series, User Manual

Search results

Summary of Contents for UCM6200 Series

Reviews:

Related manuals for UCM6200 Series

Brands by name

Popular brands