Grandstream Networks GVC3210 RMT Administration Manual Download Page 83

Page: 83 / 94

P a g e

GVC3210 Administration Guide

Version 1.0.1.21

Device Control

Device Control/Video Control

Users could add preset and manipulate EPTZ control on this page.



Move the cursor to one configured preset to preview preset.



Click one preset to apply the preset.



Click the un-configured preset, and adjust via the EPTZ control panel on the right, then save the
configurations.

Figure 15: GVC3210 Web UI - Video Control

Note

When the GVC3210 is using 4K resolution during video call, EPTZ is not supported. The GVC3210 supports
90° field of view. Please, install GVC3210 at the position that suits the best conference view if you plan to
use 4K resolution.

Use EPTZ

Control direction

keys to adjust

camera

Zoom Out

Zoom In

Empty preset

Selected but

unconfigured

preset

Preset that has

been set before

https://arttel.ru/

https://arttel.ru/shop/terminaly-vks/grandstream-gvc3210

Summary of Contents for GVC3210 RMT































































































Search results

Summary of Contents for GVC3210 RMT

Reviews:

Related manuals for GVC3210 RMT

Brands by name

Popular brands

Grandstream Networks GVC3210 RMT, Administration Manual

Search results

Summary of Contents for GVC3210 RMT

Reviews:

Related manuals for GVC3210 RMT

Brands by name

Popular brands