34
13.4.3 ELECTRONIC COIN OPERATION ON THE MACHINE
The display shows the price and cycle selected with a display
that is:
Pxx :(program number from 01 to 20)
Cycle cost: xx,xx €
The price is modified using “PLUS” and “MINUS” (field
variable from 0.00 to 99.95€ with minimum steps of 0.05€)
and the cycle is modified using “SEL”.
All programs memorised in the machine are proposed, even
those not enabled.
Re-open PRGET to end the programming, then remove and
re-apply voltage to the machine.
With the coin operation function enabled, switch the machine,
the display shows:
• the cycle selected with the maximum temperature
envisioned for that washing cycle
• The time programmed for the countdown.
“
Insert n. gettoni:xx
”or “
Make payment
” or “Make payment
of €:xx,xx”
(according on the setting selected)
Where “xx” coresponds to the value inserted (n. of tokens or
cost in €) for that cycle with PRGET activated.
During the insertion of tokens or coins the cost of the cycle
will reduce until when the last token/coin is introduced the
display will indicate a flashing“
00
”.
If the door is closed “PRESS START” will appear in the
reverse yes/no form in replacement of the previous relative
to payment. It will therefore be possible to press the kstart
button, starting the washing program.
If the door is open, two messages will appear “load the
laundry” and “close the door” and once the door is closed the
message in the previous point will appear.
On cycle start (after KSTART has been pressed) the display will
show the normal indication.
The previous messages will return when the hatch is opened
at the end of the cycle.
Any alarm signal has priority over these indications.
NOTES:
The number of tokens or coins already inserted remains
memorised if there should be a power cut.
If the number of tokens inserted exceeds those necessary for
the execution of the desired cycle, the surplus is memorised
and can be used for the successive cycle. The maximum credit
(max. number of tokens counted) is 10.
If the number of coins inserted exceeds those necessary for
the execution of the desired cycle, the surplus is memorised
and can be used for the successive cycle.
The maximum credit, i.e. the maximum value that can be
accumulated is 20.00€.
NOTE
See also coin operation setting inthe previous paragraph.
In both cases it must be possible to reset the residual credit
with the machine in IDLE-ON and door open by pressing the
Keco key 5 times in 10 seconds and the Kstart key 5 times
consecutively. The confirmation of reset takes place with a full
screen message “CREDIT RESET” for 3 seconds. The 10 second
count starts fromthe first time the Keco key is pressed.
ATTENTION!
In the coin operated version:
- Enabled drying cycles canbe carried out
- It is not possible to access programming od optional
parameters
- A pause cannot be inserted during the cycle (see “Introduction
of a pause”).
- If there is a power cut during the cycle, when the voltage
returns the cycle re-starts from the last phase that it was
performing without having to insert additional coins.
- The optional parameters enabled before insertion of P3
remain active even after enabling of coin operation (except
for “Cycle delayed start”).
In the case of electronic coin operation on the machine a coin
counter must be implemented on the machine in order to control
the operator’s earnings.
With the PRGett key activated and the two keys pressed (Gicar
on selection) the display of a scale of coins accepted is displayed.
This can be consulted using keys K+ and K- including the total
received, which can be reset by pressing another two Gicar keys
at will. Reset also affects the count of the individial coins.
By re-positioning the PRGett, the machine goes back to normal
conditions envisioned for electronic coin operation on the
machine.
ATTENTION:
In the case of programming of the cycle cost using electronic
coin operation at a value >10.00€ and successive passage
to “stepper” version, the machine will take the cost of the
cycle previously set and as it is higher than the maximum
number of coins that can be set in order to proceed with
programming, the K- key must be held down until, after the
various numbers are shown on the display, it returns to”0”.
At this point the new cycle costs can be programmed. In fact,
to pass from one preset to another in this way is not correct,
therefore in the current situation we will keep this system to
modify it if reqired successively.
Summary of Contents for EB10
Page 38: ...38...
