manualshive.com logo in svg

Grady-White Boats Seafarer 228, Owner'S Manual, Page: 31 / 66

Share
Download
Grady-White Boats Seafarer 228 Owner'S Manual Download Page 31

5-1

Chapter 5: Instrumentation

ChapTer 5: INSTrUMeNTaTION aND 

SWITCheS

Yamaha Instrumentation Panel

Grady-White installs full Yamaha Command Link or Command Link Plus instrumentation on all 

boats. The instruments are powered by the ignition key(s) and will operate when the ignition 
switch(es) is in the “on” position.

Yamaha Command Link CL7 Display (Digital Engines & Helm 

Master™)

The Yamaha display provides engine and boat information listed below. The display of these 

functions and other graphics may be customized. Please see the Yamaha owner’s manual for 
detailed instructions on customizing.

• 

Fuel Level 

This feature indicates the gas tank(s)’ fuel level. Remember two things when reading this 

gauge: 

•  The accuracy of your gauge varies with the attitude of your boat in the water (trim or list).
•  The fuel pickup tube inside the gas tank is not capable of withdrawing all of the fuel from 

the tank.

Summary of Contents for Seafarer 228



































































Reviews:

No comments