Grady-White Boats Gulfstream 232 Owner'S Manual Download Page 73 | Manualshive

Page: 73 / 76

background image

9-3

Chapter 9: Warranty

Warranty Claim Procedures

Upon the discovery of a defect, the owner is to promptly contact the Grady-White dealer from

whom the original retail purchaser purchased the boat who will affect the corrective action under
this warranty upon prior written authorization from Grady-White Boats, Incorporated.

THESE WARRANTIES ARE EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES. DURATION

OF ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR
OTHERWISE SHALL BE LIMITED TO AND COINCIDENT WITH THE DURATION OF THESE EXPRESSED
WARRANTIES.

«
...
71
72
73
74
75
...
»

Summary of Contents for Gulfstream 232













































































Reviews:

No comments

Related manuals for Gulfstream 232

NARAK CROSS 405

Brand: Nautiraid Pages: 16

Brand: NERIS Pages: 2

3 Seat Sun Slider

Brand: KL Industries Pages: 12

Brand: Scout Boats Pages: 112

Brand: Grand Soleil Pages: 103

Brand: Mercury Pages: 155

FLYBRIDGE 53 2019

Brand: Tiara Yachts Pages: 172

Brand: Gumotex Pages: 52

Brand: Supra Pages: 89

Brand: Supra Pages: 88

Nautica 450 RACE

Brand: Nautica Boats Pages: 20

Brand: Jeanneau Pages: 114

Brand: Ranger Tugs Pages: 36

Brand: Jeanneau Pages: 100

Brand: KAYAKS2FISH Pages: 20

Brand: Jilong Pages: 48

Cheyenne Extreme

Brand: Jilong Pages: 47

PATHFINDER C-II 330

Brand: Jilong Pages: 53

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands