background image

F

R E E D O M

  2 8 5

8–1

C h a p t e r   8 :   F r e e d o m   2 8 5

S p e c i f i c a t i o n s

Beam-amidship.............................................................................................

9’ 6” (2.9 m)

Bridge Clearance ..........................................................................................

6’ 4” (1.9 m)

Centerline Length .........................................................................................

28’ (8.53 m)

Keel To Top Of Windshield Bar ...................................................................

8’ (2.4 m)

Freshwater Capacity .....................................................................................

20 Gallons (75.7 L)

Fuel Capacity - Main ....................................................................................

201 Gallons (760.9 L)

Hull Draft......................................................................................................

20” (51 cm)

Engine Shaft Length .....................................................................................

Dual - 25” (64 cm)

Transom Width .............................................................................................

9’ (2.7 m)

Dry Weight ...................................................................................................

5980 Lbs (2713 kg)

Steering Type ................................................................................................

Hydraulic Tilt

Steering Hose Length ...................................................................................

22’ (6.7 m)

Maximum Outboard HP ...............................................................................

600 HP (447.4 kW)

O p t i o n a l   F e a t u r e s

A

CCESSORIES

• Convenience package - battery charger & 

power with galvanic isolator

• Deluxe bar with grill & electro-mechanical 

helm seat

• Hardtop mounted rod holders

• Head – marine head with  electric flush 

 

10 gallon (37.9 L)

• Head – marine head with  macerator, 

 

10 gal (37.9 L) holding tank & pump-out

• Head – portable with  deck pump-out

• Head – portable with  in-line macerator

• Livewell – 32 gal (121L) insulated raw 

water livewell with light, full column 
distribution inlet & ob drain 1100 gph 

 

(4164 lph) pump

• Outrigger kit- 15 ft (4.6 m) radial hardtop 

mounted

• Painted hull

• Seating - deluxe helm seat II (stbd)

• Seating - deluxe helm seat III (stbd)

• Sirius satellite radio system

• Ski pylon

• Steering - power assist

• Sun platform insert with cushions

• Wet bar with sink & electro-mechanical 

helm seat

• Yamaha Helm Master™ control system

C

ANVAS

 

(canvas available in ivory or navy)

• Bow cover with zipper

• Hardtop front & side curtains 

• Hardtop aft curtain 

• Hardtop drop curtain

• Lounge seat cover

• Tonneau cover

• Wet bar cover

Summary of Contents for Freedom 285






















































































Reviews: