Graco WB3000 Instructions - Parts Manual Download Page 57

Page: 57 / 78

Repair

Air Valve Repair

1. See

Prepare the Gun for Service, page 47

2. See

Gun Barrel Removal, page 5 0

3. Remove the screws (13) and trigger (12).
4. Remove the ES On-Off Valve. See

ES On-Off Valve Repair, page 56

5. Remove the spring (2).
6. Push on the front of the air valve shaft to force it

out the back of the handle. Inspect the rubber

seal (23a*) and replace if damaged.

7. Inspect the u-cup (3). Do not remove the u-cup

unless damaged. If removed, install the new one

with its lips facing into the gun handle (16). Place

the u-cup on the shaft of the air valve to help seat

it in the gun handle.

Figure 40 Install U-Cup

8. Install the air valve (23) and spring (2) into the

gun handle (16).

9. Install the ES On-Off Valve. See

ES On-Off Valve Repair, page 56

10. Install the trigger (12) and screws (13).
11. See

Gun Barrel Installation, page 50

Figure 41 Air Valve

3A2497C

Summary of Contents for WB3000















































































Search results

Summary of Contents for WB3000

Reviews:

Related manuals for WB3000

Brands by name

Popular brands

Graco WB3000, Instructions - Parts Manual

Search results

Summary of Contents for WB3000

Reviews:

Related manuals for WB3000

Brands by name

Popular brands