Graco WB3000 Instructions - Parts Manual Download Page 45

Page: 45 / 78

Troubleshooting

Electrical Troubleshooting

Problem

Cause

Solution

ES On/Off switch is OFF (O).

Turn ON (I).

Gun air pressure too low (ES

indicator is amber).

Check air pressure to gun; minimum

45 psi (0.32 MPa, 3.2 bar) needed at

gun for full voltage.

Atomizing air pressure too high.

Decrease.

Fluid pressure too high.

Decrease, or replace worn tip.

Incorrect distance from gun to part.

Should be 8-12 in. (200-300 mm).

Poorly grounded parts.

Resistance must be 100 ohms or

less. Clean workpiece hangers.

Faulty gun resistance.

See

Test Gun Resistance, page 36

Fluid leaks from the ﬂuid needle

packings and causes a short.

See

Fluid Needle Replacement, page 51

Poor wrap.

Faulty alternator.

See

Alternator Removal and

Replacement, page 53

ES On/Off switch is OFF (O).

Turn ON (I).

ES or Hz indicator is not lit.

No power.

Check power supply, alterna-

tor, and alternator ribbon cable.

See

Power Supply Removal and

Replacement, page 5 2

and

Alternator Removal and

Replacement, page 53

Operator not grounded or is near

ungrounded object.

See

Grounding, page 21

Operator gets mild shock.

Gun not grounded.

See

Check Gun Electrical

Grounding, page 23

, and

Test Gun Resistance, page 36

Operator gets shock from workpiece. Workpiece not grounded.

Resistance must be 100 ohms or

less. Clean workpiece hangers.

3A2497C

Summary of Contents for WB3000















































































Search results

Summary of Contents for WB3000

Reviews:

Related manuals for WB3000

Brands by name

Popular brands

Graco WB3000, Instructions - Parts Manual

Search results

Summary of Contents for WB3000

Reviews:

Related manuals for WB3000

Brands by name

Popular brands