Graco Viscount High-Flo Plus 25E932 Instructions-Parts List Manual Download Page 19

Page: 19 / 20

Technical Specifications

3A6939B

Technical Specifications

California Proposition 65

Viscount II Motor with 2500, 3000, and 4000cc Pumps

U.S.

Metric

Lower size

25E932

2500cc

25E933

3000cc

25E934

4000cc

Maximum fluid working pressure

25E932

430 psi

3.0 MPa, 29.6 bar

25E933

360 psi

2.5 MPa, 24.8 bar

25E934

270 psi

1.9 MPa, 18.6 bar

Maximum hydraulic working pressure

1500 psi

10.3 MPa, 103 bar

Maximum recommended cycle rate for
continuous duty

12 cycles per minute

Hydraulic oil consumption

See Performance Charts, page 17.

Dimensions

See Dimensions, page 15.

Weight

See Dimensions, page 15.

Maximum hydraulic motor fluid temperature

130°F 54°C

Output per cycle gallon (cc)

25E932

2500 cc per cycle

25E933

3000 cc per cycle

25E934

4000 cc per cycle

Maximum fluid temperature rating

150°F

66°C

Notes

Sound data: See Viscount II motor manual 308048.

Wetted parts: See Sealed 4-Ball Lower manual 3A5348.

CALIFORNIA RESIDENTS

WARNING: Cancer and reproductive harm – www.P65warnings.ca.gov.

Summary of Contents for Viscount High-Flo Plus 25E932





















Search results

Summary of Contents for Viscount High-Flo Plus 25E932

Reviews:

Related manuals for Viscount High-Flo Plus 25E932

Brands by name

Popular brands

Graco Viscount High-Flo Plus 25E932, Instructions-Parts List Manual

Search results

Summary of Contents for Viscount High-Flo Plus 25E932

Reviews:

Related manuals for Viscount High-Flo Plus 25E932

Brands by name

Popular brands