Graco Merkur Bellows Repair Parts Download

Page: 25 / 28

Optional Kits

312793L

Optional Kits

Use with materials that cause chemical compatibility concerns with UHMWPE, such as acid catalyst materials.

** Replaces standard kits for high corrosive applications.

Accessories

Overflow Chamber Kit 24E298

Kit Description

LB050A
LB050B

LB100A
LB100B

LB150A
LB150B

LB100C

(acid)

Reinforced PTFE V-Packing Kit*
Reinforced PTFE throat packings and glands, reinforced PTFE
piston packings and glands, o-rings, and springs

24J858

24J859

24J860

PTFE Bellows Kit*
Includes PTFE bellows and o-rings

24J850

24J851

316 Stainless Steel Check Ball Kit**
Includes: Check balls (34, 47), ball stop spring (36), and o-rings
(2, 12, 21, 32 and 41).

24T257

24T258

316 Stainless Steel Seat and Ball Kit**
Includes: Seats (33, 46), check balls (34, 47), flow-through nut
(44) and o-rings (2, 12, 21, 32, and 41).

24A800

24A801

Ref. Description

Qty.

101

LID

102

O-RING

103

BOTTLE

104

FITTING, 2 x 1/4-18 npt

105

NUT, retaining

106

D-SHAPED SEAL, bellows

Summary of Contents for Merkur Bellows





























Search results

Summary of Contents for Merkur Bellows

Reviews:

Related manuals for Merkur Bellows

Brands by name

Popular brands

Graco Merkur Bellows, Repair Parts

Search results

Summary of Contents for Merkur Bellows

Reviews:

Related manuals for Merkur Bellows

Brands by name

Popular brands