Graco Magnum Project Painter 5 Operation Manual Download | Manualshive

Page: 1 / 36

background image

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441

Copyright 2007, Graco Inc. is registered to I.S. EN ISO 9001

ti9338a

For portable spray applications of architectural paints and coatings

Model: 261800

Maximum Working Pressure: 2800 psi (19 MPa, 193 bar)
Dispense Rate: 0.24 gpm (0.91 lpm)

IMPORTANT SAFETY INSTRUCTIONS.
Read all warnings and instructions in this
manual. Save these instructions.

Use water-based or mineral spirit-type
materials only. Do not use materials having
flash points lower than 70°F (21°C). For
more information about your material
request MSDS from distributor or retailer.

Includes:

Gun: SG10

Hose: 1/4 inch x 25-ft. (6.4 mm x 7.5 m)
9 inch Pressure Roller Attachment

312079A

Operation

Project Painter 5 Airless Sprayer

The manual provided with this
sprayer contains
English and

Español.

Visit our website;
http://M

AGNUM

.Graco.com

Specifications

This equipment is not intended for use
with flammable or combustible
materials used in places such as
cabinet shops or other “factory” or fixed
locations. If you intend to use this
equipment in this type of application,
you must comply with NFPA33 and
OSHA requirements for the use of
flammable and combustible materials.

ti9208a

ti91915a

1
2
3
...
»

Summary of Contents for Magnum Project Painter 5





































Reviews:

No comments

Related manuals for Magnum Project Painter 5

Brand: Keithley Pages: 49

Brand: Teac Pages: 148

Brand: IFM Pages: 25

Brand: Campbell Pages: 16

Brand: Labom Pages: 5

Brand: IET Labs Pages: 114

Brand: Gardner Bender Pages: 7

Brand: M & I Instruments Pages: 2

Brand: Olympus Pages: 12

Brand: palintest Pages: 14

Brand: Yamaha Pages: 84

Professional Plus

Brand: YSI Pages: 28

Brand: Omega Pages: 20

Brand: Kawai Pages: 72

Brand: Vega Pages: 52

Brand: Omega Pages: 16

Brand: A&D Pages: 10

Brand: Zhengzhou Minghe Electronic Technology Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands