Graco LineLazer ES 1000 Installation, Repair, Parts Download Page 17

Page: 17 / 120

Setup/Startup

3A4603F Operation, Repair, Parts

Setup/Startup

1. Perform

Pressure Relief Procedure

, page 16

Charging the Battery

, page 13.

3. Perform

Grounding Procedure (AC Wall Power)

page 14,

or Grounding Procedure (Battery

Power) (For Flammable Flushing Fluids Only)

page 15, if using flammable materials.

4. Fill throat packing nut with TSL to prevent

premature packing wear. Do this daily or each time
you spray.
a. Place the TSL bottle nozzle into the top center

opening in the grill at the front of the sprayer.

b. Squeeze bottle to dispense enough TSL to fill

the space between the pump rod and packing
nut seal.

NOTE:

If running off wall power, plug cord into charging

port. If using an extension cord, use a 3-wire, 12 AWG
(2.5mm

) minimum with an undamaged ground contact.

5. Turn ON/OFF Switch to

OFF

6. If removed, install strainer.

7. Turn prime valve down. Turn pressure control

counterclockwise to lowest pressure.

NOTE:

Minimum hose size for proper sprayer

operation is 1/4 in. x 50 ft for LL ES 1000 and 3/8 x 20’
for ES 2000.

8. Place siphon tube set in grounded metal pail

partially filled with flushing fluid. Attach ground wire
to true earth ground. Use water to flush water-based
paint and mineral spirits to flush oil-based paint and
storage oil.

9. Turn ON/OFF Switch to ON:

ti30322a

ti27612a

ti27614a

ti27613a

ti30324a

Summary of Contents for LineLazer ES 1000

























































































































Search results

Summary of Contents for LineLazer ES 1000

Reviews:

Brands by name

Popular brands

Graco LineLazer ES 1000, Installation, Repair, Parts

Search results

Summary of Contents for LineLazer ES 1000

Reviews:

Brands by name

Popular brands