Graco Bulldog 245185 Instructions Manual Download Page 1

Page: 1 / 22

28:1/33:1 RATIO, WALL MOUNT

Bulldog

Pumps

For ambient temperature spray applications.

Part No. 245187, 33:1, Series B

3300 psi (22.8 MPa, 228 bar) Maximum Fluid Working Pressure
100 psi (700 kPa, 7 bar) Maximum Air Input Pressure

Part No. 253697, 28:1, Series A

2800 psi (19.3 MPa, 193 bar) Maximum Fluid Working Pressure
100 psi (700 kPa, 7 bar) Maximum Air Input Pressure

Part No. 245185, Series B (240 Volt Heater)
Part No. 245186, Series B (480 Volt Heater)

For heated spray applications.

3000 psi (20.7 MPa, 207 bar) Maximum Fluid

Working Pressure

90 psi (600 kPa, 6 bar) Maximum Air Input Pressure

GRACO INC.

P.O. BOX 1441

MINNEAPOLIS, MN

55440–1441

307932R

Model 245187 Shown

4414B

Instructions

Important Safety Instructions

Read all warnings and instructions in this manual.
Save these instructions.

See page 2 for Table of Contents.

Summary of Contents for Bulldog 245185























Search results

Summary of Contents for Bulldog 245185

Reviews:

Related manuals for Bulldog 245185

Brands by name

Popular brands

Graco Bulldog 245185, Instructions Manual

Search results

Summary of Contents for Bulldog 245185

Reviews:

Related manuals for Bulldog 245185

Brands by name

Popular brands