Graco 482 Series Instructions-Parts List Manual Download Page 1

Page: 1 / 24

310543

Rev. A

First choice when

quality counts.

INSTRUCTIONS-PARTS LIST

INSTRUCTIONS

This manual contains important

warnings and information.
READ AND KEEP IT FOR REFERENCE.

MODEL 482

Automatic Metering Valves

3200 psi (220 bar, 22.0 MPa) Maximum Fluid Working Pressure

Refer to page 2 for a summary of the List of Models

Part No. C02021

Model 482–B; 7/8–18 nef externally threaded fluid inlet
boss and 7/16–20 unf mounting hole

Part No. C02022

Model 482–C; 7/16–20 unf mounting hole only

U.S. Patent Nos. 3,160,331 and 3,132,775

Part No. C02025

Model 482–E; 7/16–20 unf mounting hole and 1/4
material outlet

Part No. C02026

Model 482–HA; Model 482–C with trigger-actuated
pistol grip handle

Part No. C02027

Model 482–MS; Model 482–B with seal fluid reservoir
and 7/16–20 mounting bolt for moisture sensitive fluid

Part No. C02078

Model 482–DA with double acting air cylinder and 1/4
npt(f) outlet

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

www.graco.com

Graco Inc. is registered to I.S. EN ISO 9001

Summary of Contents for 482 Series

























Search results

Summary of Contents for 482 Series

Reviews:

Related manuals for 482 Series

Brands by name

Popular brands

Graco 482 Series, Instructions-Parts List Manual

Search results

Summary of Contents for 482 Series

Reviews:

Related manuals for 482 Series

Brands by name

Popular brands