Graco 311737G Important Safety Instructions Manual Download Page 27 | Manualshive

Page: 27 / 32

background image

Power Cord Replacement

311737G

27

Power Cord Replacement

See Wiring Diagram, page 29.

Removal

1.

Follow

Control Board Replacement

removal

instructions, steps 1-8, page 20.

2.

Disconnect power cord connectors (C and D) from
control board (33).

3.

Disconnect green ground wire (G) from sprayer by
loosening grounding screw (31).

Installation

1.

Follow

Control Board Replacement

installation

instructions, steps 1-4, page 20.

2.

Reconnect, green ground wire (G) to green ground-
ing screw (31) on frame. Be sure terminal on ground
faces UP or wires could get caught in shroud.

3.

Reconnect power cord connectors (C and D) to con-
trol board (33).

4.

Reattach motor connector (B) and pressure control
switch connect (A).

5.

Install shroud (29) and two screws (30) (see illustra-
tion, page 17).

33

C

D

C

D

G

31

240V

120V

«
...
25
26
27
28
29
...
»

Summary of Contents for 311737G

































Reviews:

No comments

Related manuals for 311737G

Brand: Foamit Pages: 6

Brand: Kärcher Pages: 16

Brand: Rac Pages: 13

Brand: Kärcher Pages: 112

Brand: Paul B. Zimmerman Pages: 24

Brand: X4 TOOLS Pages: 16

Trailer HDS Series

Brand: Kärcher Pages: 32

Brand: Bella Pages: 19

Brand: Craftsman Pages: 60

Brand: Craftsman Pages: 60

Brand: lamart Pages: 120

WE6 Windfoil Electric

Brand: Rogers Pages: 17

Brand: Snap-On Pages: 15

Brand: Snap-On Pages: 29

Brand: Goldacres Pages: 24

Brand: Kärcher Pages: 14

Brand: Kärcher Pages: 20

Brand: Kärcher Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands