Graco 26C265 Instructions Manual Download Page 9 | Manualshive

Page: 9 / 40

Graco 26C265 Instructions Manual Download Page 9

Setup

311053L

9

Manifolds 288219, 288220, and 26C622

6.

In a circulating system

, connect an electrically

conductive fluid hose to the gun fluid outlet (G).

In a non-circulating system

, remove the gun fluid

outlet fitting (G) and plug the outlet port with the pipe
plug (109) supplied.

Manifold 244930

7. This manifold is equipped with passages for

circulating water to maintain the temperature of the
gun. Ports provided are:

-

Side water inlet, 1/4 npt(f)

-

Top water outlets, 1/8 npt(f)

-

Side RTD sensor, 1/8 npt(f)

See

Accessories

, page 33, for available fittings and

sensors.

F

IG

. 5: Manifolds 288219, 288220, and 26C622

KEY

C Cylinder Air Inlet: accepts 1/4 in. (6.3 mm) O.D. tubing
F Fluid Inlet: 1/4-18 nptf or #5 JIC (1/2-20 unf)
G Fluid Outlet (circulating gun only): 1/4-18 nptf or #5 JIC (1/2-20 unf)

FAN

ATOM

CYL

G (or F)

C

F (or G)

TI8113a

F

IG

. 6: Manifold 244930

KEY

L Water Outlet: 1/8 npt(f)
M Air Inlet (to open valve): 1/8 npt(f)
N Fluid Inlet: 3/8(f)
P Water Inlet: 1/4 npt(f)

L

N

L

M

P

TI8115a

TI8116a

«
...
7
8
9
10
11
...
»

Summary of Contents for 26C265









































Reviews:

No comments