background image

Instructions/Parts

AIR DRIVEN

Expanding Blade Mixer

Expanding blade bung-mounted agitator for maintaining suspension and even mixing in 
industrial paints and coatings. For professional use only.

Not approved for use in European explosive atmosphere locations.

Model 24C728, Series B

Low Viscosity, up to 1000 centipoise

Model 24C729, Series B

High Viscosity, up to 2000 centipoise

100 psi (0.7 MPa, 7 bar) Maximum Working Pressure

Contents

Warnings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Operation   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Repair   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Parts   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Technical Data   . . . . . . . . . . . . . . . . . . . . . . . . .10

Graco Standard Warranty   . . . . . . . . . . . . . . . .12

Graco Information   . . . . . . . . . . . . . . . . . . . . . .12

Important Safety Instructions

Read all warnings and instructions in this manual. 
Save these instructions.

ti14646A

313643F

ENG

Summary of Contents for 24C728













Reviews: