GPI P-120DEF Owner'S Manual Download Page 12

Page: 12 / 16

SPECIFICATIONS

PA-120DEF:

Applications

Fluids: Diesel Exhaust Fluid (DEF)

Operating Environment: Outdoor, operating temperature range

of –20° to +120° F (–30° to +50° C).

Operating Pressure

10 PSI

Pump Housing

Lightweight, durable, molded plastic housing.

Convenient 2-inch NPS bung adapter for easy

installation.

Performance

Pump Rate: Up to 12 GPM (45 LPM). Rate will vary with

temperature.

Duty Cycle: 30 minutes ON, 30 minutes OFF. Duty cycle will

vary with temperature.

Electrical Specifications

Input: 115-volt AC, grounded, GFCI protected

Cord: 18 gauge, 3 wire, grounded plug equipped with circuit

breaker.

Mechanical Connections

Bung: 2 inch NPS

Inlet:

1 inch NPT

Outlet: 1 inch NPT

Recommended Accessories

3/4 in. x 12 ft. (3.7m) DEF discharge hose

3/4 in. NPT DEF automatic nozzle

3/4 in. NPT DEF ball valve

Weight

Shipping: 15 lbs. (6.8kg)

P-120DEF:

Applications

Fluids: Diesel Exhaust Fluid (DEF)

Operating Environment: Outdoor, operating temperature range

of –20° to +120° F (–30° to +50° C).

Operating Pressure

10 PSI

Pump Housing

Lightweight, durable, molded plastic housing.

Convenient 2-inch NPS bung adapter for easy

installation.

Performance

Pump Rate: Up to 12 GPM (45 LPM). Rate will vary with

temperature.

Duty Cycle: 30 minutes ON, 30 minutes OFF. Duty cycle will

vary with temperature.

Electrical Specifications

Input: 12-volt DC

Current: 12-15 amps

Cord: 14 gauge, 15 ft. (4.6m)

Fuse: 20 amps AGC

Mechanical Connections

Bung: 2 inch NPS

Inlet:

1 inch NPT

Outlet: 1 inch NPT

Recommended Accessories

3/4 in. x 12 ft. (3.7m) DEF discharge hose

3/4 in. NPT DEF automatic nozzle

3/4 in. NPT DEF ball valve

Weight

Shipping: 15 lbs. (6.8kg)

Summary of Contents for P-120DEF

















Search results

Summary of Contents for P-120DEF

Reviews:

Related manuals for P-120DEF

Brands by name

Popular brands

GPI P-120DEF, Owner'S Manual

Search results

Summary of Contents for P-120DEF

Reviews:

Related manuals for P-120DEF

Brands by name

Popular brands