GOWIN GW2AR Series Programming And Configuration Manual Download Page 83

Page: 83 / 108

6 Configuration Mode Introduction

6.7 CPU Mode

UG290-2.5.2E

74(98)

Note!

The lower 12 bits of an SPI Flash startup address is invalid and the address space of
ADDR [23:12] can be set by users.

GW1N (R)-4 devices do not currently support automatic DUALBOOT

configuration. Gowin provides users with DUAL BOOT configuration
solution for these two devices. Please refer to

TN101-1.0, GW1N-4 FPGA

Download DUAL BOOT Program

for more details.

6.7

CPU Mode

In CPU mode, the Host configures Gowin FPGA products through the

8-bit data bus interface. CPU mode pins are shown in Table 6-17.

Table 6-17 CPU Mode Pins

Pin Name

I/O

Description

RECONFIG_N

I, internal
weak
pull-up

Low level pulse: Start GowinCONFIG

READY

I/O

High-level pulse: The device can be programmed
and configured;
Low level: Programming configuration for device is
prohibited

DONE

I/O

High-level: Successfully programmed and
configured;
Low-level: Programming and configuration
uncompleted or failed.

MODE[2:0]

I, internal
weak
pull-up

Configuration mode selection, READY rising edge
sampling

SCLK

Input clock

CLKHOLD_N

I, internal
weak
pull-up

High: CPU operation is valid
Low: CPU operation is invalid

WE_N

Read-write enable
0

：

Write

：

Read

D[7:0]

I/O

Data I/O port: Used as input pin in CPU mode, and
used as output pin after configuration for
verification

Summary of Contents for GW2AR Series













































































































Search results

Summary of Contents for GW2AR Series

Reviews:

Related manuals for GW2AR Series

Brands by name

Popular brands

GOWIN GW2AR Series, Programming And Configuration Manual

Search results

Summary of Contents for GW2AR Series

Reviews:

Related manuals for GW2AR Series

Brands by name

Popular brands