GOWIN GW2AR Series Programming And Configuration Manual Download Page 47

Page: 47 / 108

6 Configuration Mode Introduction

6.2 JTAG Configuration

UG290-2.5.2E

38(98)

Figure 6-16 Process of Background Programming

Start

Verify ID

Code

Erase Flash

Program Flash

Stop

If need to read back to verify data,

Please use

Readable-pattern

at the 1

Y-page of the 1

X-page.

Erase Internal Flash

For the embedded Flash memory of GW1N series, the embedded

Flash needs to be erased before each programming task. For data security,
the embedded Flash must be erased entirely.

The requirements for JTAG programming frequency are different

according to the different processes of the GW1N series of the embedded
Flash. Please refer to Table 6-8.

Table 6-8 TCK Frequency Requirements for JTAG

Device

TCK Frequency Range Process Code

GW1N-1
GW1N-1S

1.4MHz ~ 5MHz

GW1N(RF)-4B
GW1N(SER)-4C
GW1N(R)-9(C)
GW1NZ-1

1MHz ~ 5MHz

GW1NS(E)-2(C)

1MHz ~ 5MHz

FPGA erasure process of T Technology

The following describes the erase flow of T Technology for GW1NZ-1

in detail, as shown in Figure 6-17.
1.

Establish a JTAG link and reset the TAP;

Read the device ID CODE and check if it matches.

Erase SRAM first if it has been configured.

Send the "0x15" instruction of ConfigEnable;

Summary of Contents for GW2AR Series













































































































Search results

Summary of Contents for GW2AR Series

Reviews:

Related manuals for GW2AR Series

Brands by name

Popular brands

GOWIN GW2AR Series, Programming And Configuration Manual

Search results

Summary of Contents for GW2AR Series

Reviews:

Related manuals for GW2AR Series

Brands by name

Popular brands