GOWIN GW2AR Series Programming And Configuration Manual Download Page 87 | Manualshive

Page: 87 / 108

background image

6 Configuration Mode Introduction

6.9 I2C Mode

UG290-2.5.2E

78(98)

Figure 6-55 Connection Diagram for I

2

C Mode

FPGA

SCLK

DIN

Host

CLK

DOUT

Note!

The figure above shows the minimum system diagram of the I

2

C MODE. The MODE value

is set to "100". The connection for the other fixed pins is shown in Figure 6-1.

Figure 6-56 I

2

C Mode Timing

I

2

C is a serial transmission bus, which transmits data according to the

protocol shown in the figure above. Under normal status, both SDA and
SCL are at high level.

Table 6-21 I

2

C Configuration Timing Parameters

Prameter

Description

S

Startup
condition

A HIGH to LOW transition on the SDA line while SCL is
HIGH.

P

Stop condition

SDA jumps from low to high while SCL is HIGH.

ADDRESS

Address frame

A unique 7-bit or 10-bit sequence for each slave device
that identifies the slave device when the master device is
about to communicate with it.

R/W

Read/Write bit

Determines whether the master sends data to the slave (0)
or reads data from the slave (1).

ACK

ACK/NACK bit

Each frame in the message is followed by an ACK/NACK
bit, and Gowin FPGA returns 0 if correct.

DATA

Data

A data has 8bits, and the most significant bit is sent first.

All DATA on the I2C bus is transmitted in 8-bit bytes. Each byte sent by

the transmitter, it releases the DATA line during the clock pulse 9, and the
receiver sends back a response signal. The response signal is a valid
response bit (ACK bit) if it is low, indicating that the receiver has
successfully received the byte. The response signal is a
non-acknowledgment bit (NACK) if it is high, which generally indicates that
the receiver did not succeed in receiving the byte. The requirement for the
ACK feedback is that the receiver pulls the SDA line low during the low
level prior to the 9th clock pulse and ensures a stable low level during the

«
...
85
86
87
88
89
...
»

Summary of Contents for GW2AR Series













































































































Reviews:

No comments

Related manuals for GW2AR Series

Brand: Rain Bird Pages: 8

Brand: Gardena Pages: 4

Brand: FARFISA INTERCOMS Pages: 2

Brand: Aiwa Pages: 30

Brand: Dahua Pages: 18

Brand: XtendLan Pages: 22

Brand: BAS-IP Pages: 16

Brand: TBM Pages: 21

Brand: ICP DAS USA Pages: 4

Brand: Ravaglioli Pages: 68

SAM GENERATION 2

Brand: HALE Pages: 12

Brand: Oshkosh Corporation Pages: 92

Brand: Landscape Vibrations Pages: 8

Brand: Grundig Pages: 85

Brand: WAGO Pages: 48

Brand: Raven Pages: 47

Brand: RCA Pages: 20

Brand: RCA Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands