GOWIN GW2AR Series Programming And Configuration Manual Download Page 49

Page: 49 / 108

6 Configuration Mode Introduction

6.2 JTAG Configuration

UG290-2.5.2E

40(98)

Figure 6-17 The Embedded Flash Erasing process of T Technology

Start

Transfer

Config Enable Instruction

(0x15)

End

Run-Test 500 us

Move TAP through

Run-Test-Idle ->

Select-DR-Scan -> Capture-DR -> Shift-DR

-> Transfer 32 bits -> Exit1-DR

-> Update-DR -> Run-Test-Idle

SRAM Erase

Transfer

EFlash Erase Instruction

(0x75)

Run-Test 120 ms

Transfer

Config Disable Instruction

(0x3A)

Transfer

Read-ID-Code Instruction

(0x11)

Transfer

Repogram Instruction

(0x3C)

Transfer

Noop Instruction

(0x02)

Note!

Ignore the shading area operation during Background Programming.

FPGA erasure process of H Technology

FPGA erasure process of H Technology:

Send the "0x15" instruction of ConfigEnable;

Send the "0x75" instruction of EFlash Erase;

Move the state machine from Run-Test-Idle to Shift-DR; 32 clocks are
generated (TDI signal keeps low level). Move the state machine to
Exit1-DR at the 32th clock, and then return to Run-Test-Idle going from

Summary of Contents for GW2AR Series













































































































Search results

Summary of Contents for GW2AR Series

Reviews:

Related manuals for GW2AR Series

Brands by name

Popular brands

GOWIN GW2AR Series, Programming And Configuration Manual

Search results

Summary of Contents for GW2AR Series

Reviews:

Related manuals for GW2AR Series

Brands by name

Popular brands