GOWIN GW2AR-18 Programming And Configuration Manual Download Page 71

Page: 71 / 97

5 Configuration Mode Introduction

5.6 DUAL BOOT Configuration (Supported by LittleBee®

Family Only)

UG290-2.3E

62(87)

Table 5-16 shows the timing parameters.

Table 5-16 MSPI Configuration Timing Parameters

Name

Description

Min.

Max.

mclkp

MCLK clock period

15ns

mclkh

MCLK clock high time

7.5ns

mclkl

MCLK clock low time

7.5ns

mspis

MSPI PORT setup time

5ns

mspih

MSPI PORT hold time

1ns

mclkftco

Time from MCLK falling edge to output

10ns

readytmcsl

Time from READY rising edge to MCS_N low

100ns

200ns

readytmclk

Time from READY rising edge to first MCLK
edge

2.8μs

4.4μs

Other than the power requirements, the following conditions need to

be met to use the MSPI configuration mode:



MSPI port enable
RECONFIG_N is not set as a GPIO during the first configuration after
power up or the previous programming.



Initiate new configuration
Power-on again or trigger RECONFIG_N at one low pulse.

Figure 5-46 Multiple FPGA Connection Diagram in MSPI Configuration Mode

5.6

DUAL BOOT Configuration (Supported by LittleBee

Family Only)

The DUAL BOOT mode is a configuration mode supported by the

nonvolatile LittleBee

Family of FPGA products. In DUAL BOOT mode,

FPGA first reads bitstream data from external Flash to complete
configuration.

Summary of Contents for GW2AR-18


































































































Search results

Summary of Contents for GW2AR-18

Reviews:

Related manuals for GW2AR-18

Brands by name

Popular brands

GOWIN GW2AR-18, Programming And Configuration Manual

Search results

Summary of Contents for GW2AR-18

Reviews:

Related manuals for GW2AR-18

Brands by name

Popular brands