GOWIN GW2AR-18 Programming And Configuration Manual Download Page 66 | Manualshive

Page: 66 / 97

background image

5 Configuration Mode Introduction

5.5 MSPI

UG290-2.3E

57(87)

is required, users can remotely write the configuration data into the external
Flash, and trigger RECONFIG_N or power up again to upgrade the system
if the upgrade conditions are met.

MSPI Mode Pins

The configuration of the MSPI mode is shown in Table 5-15.

Table 5-15 Pin Description in JTAG Configuration Mode

Pin Name

I/O

Description

RECONFIG_N

I,
Internal
weak
pull-up

Low level pulse: Start GowinCONFIG

READY

I/O

High-level pulse: The device can be programmed and
configured;
Low level: Programming configuration for device is
prohibited

DONE

I/O

High-level pulse: Successfully programmed and
configured;
Low-level pulse: Programming and configuration
uncompleted or failed.

MODE[2:0]

I,
Internal
weak
pull-up

MODE select signal, READY rising edge sample

MCLK

O

FPGA output clock

MCS_N

O

Chip selection signal, active low.

MO

O

FPGA outputs data to Slave

MI

I

Input data to FPGA through Slave

FASTRD_N

I

READY signal rising edge sampling
High level: Read SPI mode (SPI instruction:0x03)
Low level: Fast Read SPI mode (SPI instruction:0x0B)

Note!

The MSPI configuration mode clock frequency should not be greater than 70MHz. The
Flash high-speed access mode and external pull-down FASTRD_N pin are required when
the clock frequency is greater than 30MHz and less than 70 MHz. Leave the FASTRD_N
pin floating if the clock frequency is less than 30 MHz.

«
...
64
65
66
67
68
...
»

Summary of Contents for GW2AR-18


































































































Reviews:

No comments

Related manuals for GW2AR-18

Brand: Data Aire Pages: 28

Brand: Safeline Pages: 12

Brand: Union Instruments Pages: 63

Foxtrot C-IT-0908S

Brand: TECO Pages: 4

Brand: Tractel Pages: 162

Brand: fadini Pages: 12

Brand: Locinox Pages: 63

Brand: Fenix Pages: 24

Brand: Jet Pages: 40

Brand: National Instruments Pages: 297

duplex DC -24 II

Brand: JETI model Pages: 52

Brand: Micronix Pages: 16

Brand: CarlStahl Pages: 28

Brand: Midland Pages: 92

G2+ Soul S5110 Art 4

Brand: golmar Pages: 36

Brand: ICP DAS USA Pages: 4

Brand: Axema Pages: 4

Brand: ENFORCER Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands