GOWIN GW2AR-18 Programming And Configuration Manual Download Page 35

Page: 35 / 97

5 Configuration Mode Introduction

5.2 JTAG Configuration

UG290-2.3E

26(87)

TCK 1

TCK 2

TCK 3

TCK 4

TCK 5

TCK 6

TCK 7

TCK 8

value

4. Move the state machine, back to Run-Test-Idle after going from

Exit1-IR to Update-IR, and then run the state machine at least 3 clock
cycles in Run-Test-Idle.

5. Move the state machine to Shift-DR, send 32 clock cycles, and set

TMS to high level before the 32nd clock is sent. When the 32 clock
cycles are completed, jump from Shift-DR to Exit1-DR. During this
period, sending 32 clocks can read 32 bits data, that is, 0x0100381B,
as shown in Figure 5-12;

6. Move the state machine back to Run-Test-Idle;

Figure 5-10 Read Machine Flow Chart in ID Code State

Start

Move TAP to Shift-IR

Transfer

Read ID Code(0x11)

instruction (LSB)

Move TAP to Exit1-IR

End

Move TAP to Update-

Move TAP to Run-

Test-Idle

Move TAP to Shift-DR

Transfer 32 clocks to

get ID Code

Move TAP to Exit1DR

Move TAP to Update-

Move TAP to Run-

Test-Idle

Figure 5-11 The Access Timing of Read ID Code Instruction- 0x11

Summary of Contents for GW2AR-18


































































































Search results

Summary of Contents for GW2AR-18

Reviews:

Related manuals for GW2AR-18

Brands by name

Popular brands

GOWIN GW2AR-18, Programming And Configuration Manual

Search results

Summary of Contents for GW2AR-18

Reviews:

Related manuals for GW2AR-18

Brands by name

Popular brands